Mini 10 Gigabit Copper and Fiber Media Converter Unmanaged
Introduction of 10G media converter
- TA810-10G supports two types media for network connection such as 10G Base-T and 10G SFP+ and realizes 10 Gigabit Ethernet communication across fiber via the SFP or SFP+ port with intelligent configuration features such as link fault pass-through, auto laser shutdown, port speed setting, etc.
- The media converter is designed with a switch controller and buffer memory that connects two types segments to operate smoothly.
- Auto-Negotiation – automatically determines the best connection speed
- 1/2.5G/10Gb LAN to 10G SFP+ port supports Singlemode and multimode, single or dual fiber
- With external power unit, it provides good stability and reliability.
Key Features of unmanaged fiber Ethernet converter
- Support 10K Bytes Jumbo Frame
- Transparent Transport and very low delay
- Support ITUT prescribed DWDM/CWDM wavelength
- Support to install into 1U Rack 12 slot Rack
- Full State Led display
- Easy installation
- UTP cable length detection(only RJ45 interface)
Specification of SFP+ fiber optic converter
| Transmission Speed | 10M/100M/1.25G/2.5G/5G/10Gb/s |
| Protocols | IEEE802.3an(10Gbase-T) ,IEEE802.3ae(10Gbase-SR/LR/ER/ZR) |
| Interface Type | Type: RJ45 To/From SFP+ |
| Transmission Distance | Up to SFP module (Max 40Km) Up to SFP+ module (Max 80Km) Up to SFP module (Max 40Km) Up to XFP module (Max 80Km) 10Gbase-T: 100meters Cat .6a cable |
| Maximum Packet Forwarding Rate | 14,880,950/S |
| Power Requirement | Standalone: DC 5-12V (external power) Power consumption: ≤5W |
| MAC Address | 2K |
| Jumbo Frame | 10K |
| Cable Type(Fiber) | Multimode 50/125µm, 62.5/125µm
Single-mode 9/125µm |
| Cable Type(Copper) | UTP Cat 5, 5e, 6,6a Cable |
| DIP Switch | LFP/ALS/Media Conversion Mode(see bottom table) |
| LED Indicatiors | TP/LNK,SPD,FX/LNK,PWR |
| Work Environment | Operating Temp: 0~ 50 ℃ Storage Temp: -10~ 70 ℃ Humidity: 5%~90%(non-condensing) |
| Housing | Metal, IP30 |
| Dimension | Standalone :60 (W) x 20 (H) x 90 (L) (mm) |
| Weight | 0.12kg |
| Function | Status | Description |
| LFP | Off | LFP Disable |
| On | LFP Enable |
| ALS | Off | Disable |
| On | Enable |
| Media Conversion Mode | Off | 1:TP=10G,FX=10G
2:TP=10/100/1000M, FX=1G |
| On |
| Off | TP=10/100/1000M/10G, FX=10G |
| On |
Notes:
1. LFP: Link fault pass through, When enabled, the UTP receiver is passed to the fiber transmitter to make the media converter appear transparent to the connected end devices. It uses link fault passthrough to indicate when far-end fault issues occur. If a fault occurs, the end device indicates a failure for troubleshooting.
2. ALS: automatic laser shutdown is a procedure to automatically shut down the laser when there is no input light and stop emitting optical signals.
3. FX: Optical Fiber Port
4. FX Reset: When enabled, the PoE will restart if there is no data input to the UTP receiver.
Application of fiber media converter
- Connection between fiber to copper 1.25G~10Gbps Ethernet equipment function as fiber-to-copper media converter for long distance transmission
- Media converter for network backbone(SAN, LAN, MAN)
- Can be applied in Telecommunication room, R&D laboratory, Data center, and etc.
Dimension of 10G commercial optical converter
Product Tags:
|
|
1G 10G Unmanaged Copper SFP+ Fiber Ethernet Media Converter DC12V With DIP Images
|
